Why Is The Kitchen Sink Vent Located Beneath The Window?
Why Is The Kitchen Sink Vent Located Beneath The Window?
The kitchen sink vent is typically located beneath the window because this allows proper ventilation to the outside of the home.
This helps to prevent water vapour and odours generated while using the sink from accumulating in the kitchen. The vent also helps to reduce moisture build-up and the growth of mould and mildew in the kitchen, which can cause health issues. By positioning the vent beneath the window, the air can escape outside more easily and provide more comprehensive ventilation.
Location does not matter nearly as much as appropriate sink ventilation. Many homeowners choose to install sinks beneath their exterior windows for the following reasons:
Exposure To Direct Sunshine.
You will always have enough light to wash your dishes in the morning, and you will conserve electricity during the day. At the same time, you will enjoy the scenery and even clean the dishes.
The Wind And The Breeze.
Windows are the finest places in the kitchen to harness the power of nature. While completing the chores, you will be able to smell your lovely garden and keep the kitchen fresh.
This also removes the stink of stale dishes and sewage gases from blocked sinks. All bad odors will be gone as soon as you open the window.
Look After Your Children While Doing The Dishes.
It’s even better if the window overlooks the yard or garden so you can keep an eye on your kids when they’re playing.
Cosmetics.
Kitchens are built with functionality in mind first and foremost. As a result, there aren’t many focus spots that draw attention. A vintage sink near a sun-drenched window will quickly become the focal point of your kitchen, and you’ll find yourself spending more time there.
Lower Installation Costs.
Installing a central vent beneath a window allows hot and cold water to run in a single route and around a single wall. As a result, the installation process is both cost-effective and rapid. This is also true while building the sewage line.
Effective Storage.
Because you can’t put so many things under a window, why not utilize this area for a kitchen sink? As a consequence, you’ll have enough room to install an extra cabinet and keep some extra stuff within.
How To Vent A Kitchen Sink Under A Window?
Understanding how to vent a kitchen sink through a window is critical because the air pressure from the pipes causes the P-traps to become empty.
The vent pipe is run horizontally under a window until it connects to the main building drain. The vent pipe should be angled upwards. Here’s how you vent a kitchen sink through a window:
Connect The Waste Drain Pipe And The Sink.
Within the wall hollow lies the primary drain line. To be functional, the tee must be put within 3 feet of the bottom of the P-trap.
Consult your local plumbing inspector to ensure that you utilize the proper length of vents and adhere to the local venting code. Add a 2-by2-by-1.5-inch PVC sanitary T-connector to connect the horizontal vent pipes to the 2-inch waste drain pipe from the toilet.
The fitting features three holes: a two-inch opening on the sides that leads to the sink pipe, a two-inch opening on the bottom, and a 1.5-inch opening on the top.
Set Up The Vent Pipe.
Determine the location of the vent pipe. Look for a modest spacing between the vent pipe and the sanitary T-top.
After that, the vent pipe runs horizontally through the wall studs until it reaches a vertical drain line. The vent then continues to climb from the outer wall.
Screw The Pipe Into The Hole.
Cut a 1.5-inch vertical PVC strip using the hacksaw. Attach the piece of pipe to the aperture of the sanitary T-fitting with PVC primer and glue.
The length of vents varies according to the slope and breadth of the horizontal drain pipe. However, the international plumbing code requires that it be roughly two inches long.
Draw A Line That Extends Past The Window.
The slope and length of the horizontal vent drain should be measured. To reflect the information, draw a line on the wall studs. The horizontal vent pipe should slope upward at 14 inches every foot, according to the curved line on the wall studs.
Make A 1 3/4-Inch Hole.
Drill a 1 5/8-inch hole in each stud space between the elbow and the vent’s rising point, making that each hole is on the sketched line.
Connect the horizontal pipe to the elbow by pushing it through the perforations in the pipe. Attach the second fitting at the end of the horizontal pipe with the gap pointing upwards.
Put In A PVC Vent Pipe.
Drill through your ceiling plates to install a straight-up PVC vent pipe to the attic. Connect another PVC elbow to the vent pipe once you’ve finished.
The attic vent pipe should be horizontally sloped until it reaches the soil stacks and central vents.
Join The Vent Pipe To The Stack.
Vent pipes with a diameter of three or four inches are permitted by local code. Connect the vent pipe to the stack with a PVC T-fitting. The tee should be the same size as the stack and the 1.5-inch sink vent pipe. It’s preferable to utilize the same materials on your central or other vents when following the step-by-step method.
Use the same PVC pipes and PVC adhesive to connect the pipes for your kitchen sink drain vent. Also, while cutting a channel through the attic for your new vent, make sure it slopes no less than a quarter-inch every foot.